Water Conditioners

Microbe-Lift Sludge-Away naturally speeds up the elimination of slow degrading organic sludge and muck from ponds, especially which contain rock or gravel. This organic and microbial-based method prevents toxic gasses from deriving off of hard-to-reach accumulated organic matter, protecting your fish, plants as well as marine life while clarifying your water at the same time.

• Speeds up the elimination of organic sludge & muck
• 100% active, organic & microbial-based ingredients
• Protects your fish and pond from arising toxic gasses
• This quickly disperses & is safe for the environment
• 1 gallon of water treats a 500 gal pond for 5 weeks

A liquid extract of barley straw especially helpful where bottom drains are present. An environmentally responsible, cost-efficient pond conditioner that is a clean and easy, natural and organic approach to a healthy pond environment.

• An Environmentally Responsible, Cost Efficient Pond Conditioner
• Clean And Easy
• Natural and organic approach to a health pond environment
• Goes To Work On Contact
• An environmentally responsible, cost efficient pond conditioner

Microbe-Lift Algaway 5.4 stops algae growth in your pond. No more green water! Algaway 5.4 can be applied to areas that contain fish and plants, as it will not harm either fish or live ornamental plants. When used according to the instructions, you will see a huge difference in 48 hours.

• Stops algae growth in ponds and can be applied to areas that contain fish and plants
• Control strong algae
• Will not harm fish or live ornamental plants

Microbe-Lift Nite-Out II is specifically designed for aquariums with marine life. This special formula is made to help eliminate ammonia by a natural biological process known as nitrification.

• Initiates nitrification and promotes stable nitrification
• Provides stable cold weather nitrification
• Safe to use around plants and animals

The cultures inside of Nite-Out II will establish, promote or stabilize and maintain nitrification in aquariums. This will effectively eliminate toxic ammonia.

Microbe-Lift Nite-Out II is specifically designed for aquariums with marine life. This special formula is made to help eliminate ammonia by a natural biological process known as nitrification.

• Initiates nitrification and promotes stable nitrification
• Provides stable cold weather nitrification
• Safe to use around plants and animals

The cultures inside of Nite-Out II will establish, promote or stabilize and maintain nitrification in aquariums. This will effectively eliminate toxic ammonia.

Microbe-Lift Special Blend helps to break down decaying organic matter and cycle elements like nitrogen and sulfur to prevent them from building up in your aquarium. This formula will reduce water changes and cleaning maintenance with chemical free ingredients, by lowering ammonia levels and nitrates while removing odors, clarifying water and breaking down protein foam as well as residue on gravel, plants and rocks. As this Special Blend sustains your aquarium water, plant growth is naturally stimulated while light, water and nutrients are better absorbed into plants for freshwater and saltwater aquariums. This biological maintainer is suitable to use as an aquarium starter for biological cycling and boosting. Activated carbon and copper based products are compatible with this formula.

• Helps to break down decaying organic matter and cycle elements
• Reduces maintenance & lowers ammonia and nitrates from water
• Breaks down protein foam and residue on gravel, plants and rocks
• Odors will be eliminated and water clarification will be activated
• Plant growth is naturally stimulated and presents better absorption

Microbe-Lift Special Blend helps to break down decaying organic matter and cycle elements like nitrogen and sulfur to prevent them from building up in your aquarium. This formula will reduce water changes and cleaning maintenance with chemical free ingredients, by lowering ammonia levels and nitrates while removing odors, clarifying water and breaking down protein foam as well as residue on gravel, plants and rocks. As this Special Blend sustains your aquarium water, plant growth is naturally stimulated while light, water and nutrients are better absorbed into plants for freshwater and saltwater aquariums. This biological maintainer is suitable to use as an aquarium starter for biological cycling and boosting. Activated carbon and copper based products are compatible with this formula.

• Helps to break down decaying organic matter and cycle elements
• Reduces maintenance & lowers ammonia and nitrates from water
• Breaks down protein foam and residue on gravel, plants and rocks
• Odors will be eliminated and water clarification will be activated
• Plant growth is naturally stimulated and presents better absorption

Microbe-Lift Special Blend helps to break down decaying organic matter and cycle elements like nitrogen and sulfur to prevent them from building up in your aquarium. This formula will reduce water changes and cleaning maintenance with chemical free ingredients, by lowering ammonia levels and nitrates while removing odors, clarifying water and breaking down protein foam as well as residue on gravel, plants and rocks. As this Special Blend sustains your aquarium water, plant growth is naturally stimulated while light, water and nutrients are better absorbed into plants for freshwater and saltwater aquariums. This biological maintainer is suitable to use as an aquarium starter for biological cycling and boosting. Activated carbon and copper based products are compatible with this formula.

• Helps to break down decaying organic matter and cycle elements
• Reduces maintenance & lowers ammonia and nitrates from water
• Breaks down protein foam and residue on gravel, plants and rocks
• Odors will be eliminated and water clarification will be activated
• Plant growth is naturally stimulated and presents better absorption

Provides a natural aquarium ecosystem, for better overall fish health and improved water quality For SALT & FRESH WATER. Reef Safe. Saltwater environments the bacteria in this product will remain effective when used in marine environments with a specific gravity of 1.017 to 1.025. In new marine tanks, add the aquarium salt mix and allow the water to circulate for 24 hours, then check and adjust the density. Add the bacteria after the water has circulated for the 24-hour period. Saltwater oceans are a highly stable environment with very little fluctuation in pH.

• Increases resistance to pathogens and parasites - see product description below for use.
• Promotes fish growth and improves dissolved oxygen levels
• Biologically supports a healthy aquarium eco-system which results in a beneficial breeding environment
• Stimulates fishs immune system
• This product is NOT a chemical. It is harmless to humans, animals, fish and plants.

The ocean waters dilute fish waste and organic matter. The bacteria in MICROBE-LIFT/TheraP provides the assistance needed to break down the decaying organic matter and cycle certain elements, e.g. carbon and nitrogen, etc. which may build up in your tank. MICROBE-LIFT/TheraP has a hydrogen sulfide odor, which will dissipate quickly. All MICROBE-LIFT bacterial products may be used together. However when using multiple MICROBE-LIFT bacterial products, reduce the dosage rate of the 2nd product by 50%. After administering the bacteria, monitor your pH. Since each bottle of MICROBE-LIFT is grown individually, color variations may exist from bottle to bottle. These variations in color are not indicative of variations in product quality. Any floating particles present are suspended biofilm which slough off the sides of the bottle. Dimpling or expansion of the container is caused by pressure differences resulting from temperature variations due to the fact that the bottle is sealed.This product is NOT a chemical. It is harmless to humans, animals, fish and plants.

Microbe-Lift Nite-Out II is specifically designed for aquariums with marine life. This special formula is made to help eliminate ammonia by a natural biological process known as nitrification.

• Initiates nitrification and promotes stable nitrification
• Provides stable cold weather nitrification
• Safe to use around plants and animals

The cultures inside of Nite-Out II will establish, promote or stabilize and maintain nitrification in aquariums. This will effectively eliminate toxic ammonia.

Microbe-Lifts Xteme Water Conditioner is a buffered liquid water conditioner for aquariums which removes and detoxifies chlorine and ammonia wile destroying chloramines. Nitrite, copper and heavy metals are also detoxified while the waters alkalinity boosts.

• Detoxifies Nitrite
• Destroys and removes Chloramines
• 4oz treats up to 240 gallons.
• Removes Ammonia

Microbe-Lifts Xteme Water Conditioner is a buffered liquid water conditioner for aquariums which removes and detoxifies chlorine and ammonia wile destroying chloramines. Nitrite, copper and heavy metals are also detoxified while the waters alkalinity boosts.

• Detoxifies Nitrite
• Destroys and removes Chloramines
• 4oz treats up to 240 gallons.
• Removes Ammonia

Microbe-Lifts Xteme Water Conditioner is a buffered liquid water conditioner for aquariums which removes and detoxifies chlorine and ammonia wile destroying chloramines. Nitrite, copper and heavy metals are also detoxified while the waters alkalinity boosts.

• Detoxifies Nitrite
• Destroys and removes Chloramines
• 4oz treats up to 240 gallons.
• Removes Ammonia

The Microbe-Lift Aquatic Turtle Bacterial Water Balancer will naturally decreases organic waste on your ornaments, gravel and filter systems while also plummeting or even removing pathogenic bacteria. This is possible by adding beneficial bacteria into your turtles environment with this formula. This formula also reduces turtle loss, helps to clean your power filters and decreases aquarium maintenance.

• Naturally decreases organic waste on your ornaments, gravel and filter systems
• This formula can even plummet or even completely remove pathogenic bacteria
• Reduces turtle loss, helps clean your power filters and decreases maintenance

Microbe-Lift Professional is a blend of microbes that contain specifically formulated strains of bacteria manufactured for use by landscape, irrigation and pond professionals. PBL is a combination of 3 products: PL 80%, Ensure 10% and TheraP 10%. The Ensure is for plants and TheraP is for fish. Designed for professional service people so they dont have to carry 3 bottles from pond to pond.

• Keeps your ponds clean and clear
• Reduces ammonia and nitrogen levels
• Remains effective over a wide range of pH conditions
• Reduces buildup of bird droppings, fish food and dead leaves
• 1 quart treats a 1,000 gallon pond for two months (a 5,000 gallon pond requires 46 oz. for the same two month period)

Microbe-Lift Autumn/Winter Prep helps accelerate the decomposition of leaves, sediment and other organic matter during the fall and winter months. It will also jump start your pond to a healthier environment in the spring.

• A two part system of liquid bacteria and dry, water soluble packets containing a blend of cellulose enzymes
• Continues To Provide Sustained Biological Activity Even In Water Temperatures Under 40 Degree Fahrenheit
• If Frozen, Bacteria Will Remain Effective After Thawing Out; Cellulose Producing Bacteria And A Cold Weather Bacteria
• Easy to Dose in Fall or Spring
• Reduce Buildup of Organic Debris

Fritz Complete is a concentrated, one-step, full-spectrum water conditioner that detoxifies chlorine, chloramine, heavy metals, ammonia, nitrite, and nitrate. Safe to use in fresh and saltwater, including reef and planted aquariums. Use when setting up new aquariums, performing water changes, or to quickly alleviate high ammonia, nitrite, and nitrate.

• Full-spectrum water conditioner
• Does not affect pH
• Will not over-activate skimmers
• Economical concentrated formula
• One-step nitrogen cycle management

Use 1 tsp (5 ml) per 50 U.S. gallons (189 L)

Fritz Complete is a concentrated, one-step, full-spectrum water conditioner that detoxifies chlorine, chloramine, heavy metals, ammonia, nitrite, and nitrate. Safe to use in fresh and saltwater, including reef and planted aquariums. Use when setting up new aquariums, performing water changes, or to quickly alleviate high ammonia, nitrite, and nitrate.

• Full-spectrum water conditioner
• Does not affect pH
• Will not over-activate skimmers
• Economical concentrated formula
• One-step nitrogen cycle management

Use 1 tsp (5 ml) per 50 U.S. gallons (189 L)

FritzPro A.C.C.R. is a unique, highly-concentrated powder that completely, instantly, and safely detoxifies ammonia, chlorine, and chloramine from fresh and saltwater. FritzPro A.C.C.R is non-toxic and can be safely used in all types of fish and aquatic invertebrate culture.

• Concentrated dry formula
• Will not negatively affect biological filtration
• Will not affect dissolved oxygen levels in the water
• Non toxic to fish, invertebrates, aquatic plants, humans and pets
• Safe for use with food fish and shellfish

1 teaspoon will treat approx. 40 gallons (151 L) or 32 g per 1,000 L (264 gallons)

FritzPro A.C.C.R. is a unique, highly-concentrated powder that completely, instantly, and safely detoxifies ammonia, chlorine, and chloramine from fresh and saltwater. FritzPro A.C.C.R is non-toxic and can be safely used in all types of fish and aquatic invertebrate culture.

• Concentrated dry formula
• Will not negatively affect biological filtration
• Will not affect dissolved oxygen levels in the water
• Non toxic to fish, invertebrates, aquatic plants, humans and pets
• Safe for use with food fish and shellfish

1 teaspoon will treat approx. 40 gallons (151 L) or 32 g per 1,000 L (264 gallons)

FritzZyme MONSTER 360 is a powerful, concentrated probiotic blend of naturally occurring, environmentally friendly, live heterotrophic bacteria capable of digesting organic sludge common in aquariums. Fritz Zyme MONSTER 360 has been specially formulated to handle the organic waste produced by monster fish

• Super concentrated
• Promotes a clean, clear and healthy aquarium
• Reduces and simplifies maintenance
• Eliminates foul odors and improves water clarity
• Bacteria rapidly digest waste

Initial dose: Use 1 tsp (5 ml) per 25 US gallons (95 L). Maintenance dose: Use 1 tsp (5 ml) per 50 gallons (190 L). Shake well, add directly to the aquarium in an area of high flow to allow the product to circulate. Turn off UV sterilizers for 48 hours after application. NOTE: An earthy odor is normal, a natural result of biological activity. The odor will quickly dissipate when adding products to the aquarium. Color variation is normal.

FritzZyme MONSTER 460 is a powerful, concentrated probiotic blend of naturally-occurring, environmentally-friendly, live saltwater-specific heterotrophic bacteria capable of digesting organic sludge common in aquariums. Fritz Zyme MONSTER 460 has been specially formulated to handle the organic waste produced by monster fish

• Super concentrated biological aquarium cleaner for saltwater
• Promotes a clean, clear and healthy aquarium
• Reduces and simplifies maintenance
• Bacteria rapidly digests waste
• Eliminates foul odors and improves clarity

Initial dose, use 1 tsp (5 ml) per 25 US gallons (95 L). Maintenance dosing, use 1 tsp (5 ml) per 50 gallons (190 L). Shake well, add directly to the aquarium in an area of high flow to allow the product to circulate. Turn off UV sterilizers for 48 hours after application. NOTE: An earthy odor is normal, a natural result of biological activity. The odor will quickly dissipate when adding products to the aquarium. Color variation is normal.

Cloudy, discolored water is caused by overfeeding, biological blooms, gravel dust and other suspended particles that are too fine to be removed by mechanical filtration and stay in the water column. Fritz Clarifier rapidly clears water by pulling together (flocculating) fine particles, allowing them to be removed by the filter or settle to the bottom, leaving your aquarium crystal clear

• Quickly clears cloudy water
• Made in the USA
• Improves filter efficiency
• For fresh and saltwater systems, plant and reef safe
• Phosphate-free

Use 1 tsp (5 ml) per 10 U.S. gallons (38 L). Water will clear rapidly. Repeat as needed, allowing 6 hours between doses

Ammonia poisoning is the most common killer of aquarium fish. Dangerous ammonia levels often occur in new aquariums or in an established tank when adding new livestock, when a filter stops working due to power or mechanical failure, or if existing beneficial bacterial colonies are lost due to the use of medications or sudden change in water conditions. Fritz A.C.C.R. is a true complete water conditioner that not only neutralizes toxic ammonia but also the chlorine and chloramines found in tap water. Fritz A.C.C.R. is extremely safe even when overdosed.

• Water Conditioner/Ammonia Remover
• Instant Toxic Ammonia Removal
• Removes Chlorine and Chloramine from Tap Water
• Safe and Easy to Use
• Will not alter pH or deplete oxygen levels

Use 1 cap (1 tsp/5 ml) per 10 U.S. gallons (38 L). Recommended for use with salicylate-based test kits. May interfere with Nessler or other reagent-based tests. Dosage can be safely increased or repeated up to 3x

FritzZyme 360 is a powerful probiotic blend of naturally occurring, environmentally friendly, live heterotrophic bacteria capable of digesting organic sludge common in aquariums. Sludge includes fish waste, leftover food, and other decaying organic matter. Using FritzZyme 360 as part of a regular maintenance program will greatly reduce aquarium care including gravel vacuuming, water changes as well as prolonging filter media life.

• Promotes a clean, clear and healthy aquarium
• Reduces and simplifies maintenance
• Bacteria rapidly digest waste
• Eliminates foul odors
• Improves flow through filters

Initial dose: Use 1 tsp (5 ml) per 5 US gallons (19 L). Maintenance dosing: Use 1 tsp (5 ml) per 10 gallons (38 L). Shake well, add directly to aquarium in an area of high flow to allow product to circulate. Turn off UV sterilizers for 48 hours after application. NOTE: An earthy odor is normal, a natural result of biological activity. Odor will quickly dissipate when adding product to aquarium. Color variation is normal.

Hikari Betta Ultimate is an effective conditioner to make new aquarium water safe for fish and aquatic plants. It destroys chloramines, eliminates ammonia, eliminates chlorine, detoxifies nitrite and detoxifies heavy metals (including copper), providing numerous health benefits for your aquarium fish.

• Makes water your betta will love...from tap water
• Destroys Chloramines
• Eliminates Ammonia and Chlorine

Selectively replaces missing skin slime (only where missing). Adds essential electrolytes for good health. Buffers the water (boosts alkalinity). Reduces stress. Instantly "ages" your bettas water. Easy-to-use, cannot be overdosed. Gives your betta its best chance at a healthy environment.

Aquarium Solutions Ultimate Water Conditioner by Hikari is the worlds first full-function water conditioner. With everything you need in one bottle to maintain a superior environment for your aquatic pets.

• Removes chlorine and ammonia
• Destroys chloramines
• Detoxifies nitrite and heavy metals including copper
• Replaces skin slime coat on fish

1 oz Treats 60 Gallons
4 oz Treats 240 Gallons
16 oz Treats 960 Gallons
1 Gallon Treats 7,680 Gallons
5 Gallons Treats 38,400 Gallons

Aquarium Solutions Ultimate Water Conditioner instantly "ages" water allowing you to enjoy your pets in action quicker without fear of the negative impact of toxic chloramine, ammonia, chlorine, heavy metals or nitrite. Great For Freshwater, Marine or Pond Environments.

Destroys Chloramines Removes Ammonia Removes Chlorine Detoxifies Nitrite Detoxifies Heavy Metals (including Copper) Adds Essential Electrolytes Boosts Alkalinity Replaces Skin Slime-Coat Reduces Fish Stress Instantly "Ages" Water Makes A Safe Environment For Your Aquatic Pets Non-Toxic To Humans, Pets and Aquatic Life.

Aquarium Solutions Ultimate Water Conditioner by Hikari is the worlds first full-function water conditioner. With everything you need in one bottle to maintain a superior environment for your aquatic pets.

• Removes chlorine and ammonia
• Destroys chloramines
• Detoxifies nitrite and heavy metals including copper
• Replaces skin slime coat on fish

1 oz Treats 60 Gallons
4 oz Treats 240 Gallons
16 oz Treats 960 Gallons
1 Gallon Treats 7,680 Gallons
5 Gallons Treats 38,400 Gallons

Aquarium Solutions Ultimate Water Conditioner instantly "ages" water allowing you to enjoy your pets in action quicker without fear of the negative impact of toxic chloramine, ammonia, chlorine, heavy metals or nitrite. Great For Freshwater, Marine or Pond Environments.

Destroys Chloramines Removes Ammonia Removes Chlorine Detoxifies Nitrite Detoxifies Heavy Metals (including Copper) Adds Essential Electrolytes Boosts Alkalinity Replaces Skin Slime-Coat Reduces Fish Stress Instantly "Ages" Water Makes A Safe Environment For Your Aquatic Pets Non-Toxic To Humans, Pets and Aquatic Life.

Aquarium Solutions Ultimate Water Conditioner by Hikari is the worlds first full-function water conditioner. With everything you need in one bottle to maintain a superior environment for your aquatic pets.

• Removes chlorine and ammonia
• Destroys chloramines
• Detoxifies nitrite and heavy metals including copper
• Replaces skin slime coat on fish

1 oz Treats 60 Gallons
4 oz Treats 240 Gallons
16 oz Treats 960 Gallons
1 Gallon Treats 7,680 Gallons
5 Gallons Treats 38,400 Gallons

Aquarium Solutions Ultimate Water Conditioner instantly "ages" water allowing you to enjoy your pets in action quicker without fear of the negative impact of toxic chloramine, ammonia, chlorine, heavy metals or nitrite. Great For Freshwater, Marine or Pond Environments.

Destroys Chloramines Removes Ammonia Removes Chlorine Detoxifies Nitrite Detoxifies Heavy Metals (including Copper) Adds Essential Electrolytes Boosts Alkalinity Replaces Skin Slime-Coat Reduces Fish Stress Instantly "Ages" Water Makes A Safe Environment For Your Aquatic Pets Non-Toxic To Humans, Pets and Aquatic Life.

Aquarium Solutions Ultimate Water Conditioner by Hikari is the worlds first full-function water conditioner. With everything you need in one bottle to maintain a superior environment for your aquatic pets.

• Removes chlorine and ammonia
• Destroys chloramines
• Detoxifies nitrite and heavy metals including copper
• Replaces skin slime coat on fish

1 oz Treats 60 Gallons
4 oz Treats 240 Gallons
16 oz Treats 960 Gallons
1 Gallon Treats 7,680 Gallons
5 Gallons Treats 38,400 Gallons

Aquarium Solutions Ultimate Water Conditioner instantly "ages" water allowing you to enjoy your pets in action quicker without fear of the negative impact of toxic chloramine, ammonia, chlorine, heavy metals or nitrite. Great For Freshwater, Marine or Pond Environments.

Destroys Chloramines Removes Ammonia Removes Chlorine Detoxifies Nitrite Detoxifies Heavy Metals (including Copper) Adds Essential Electrolytes Boosts Alkalinity Replaces Skin Slime-Coat Reduces Fish Stress Instantly "Ages" Water Makes A Safe Environment For Your Aquatic Pets Non-Toxic To Humans, Pets and Aquatic Life.

Aquarium Solutions Ultimate Water Conditioner by Hikari is the worlds first full-function water conditioner. With everything you need in one bottle to maintain a superior environment for your aquatic pets.

• Removes chlorine and ammonia
• Destroys chloramines
• Detoxifies nitrite and heavy metals including copper
• Replaces skin slime coat on fish

1 oz Treats 60 Gallons
4 oz Treats 240 Gallons
16 oz Treats 960 Gallons
1 Gallon Treats 7,680 Gallons
5 Gallons Treats 38,400 Gallons

Aquarium Solutions Ultimate Water Conditioner instantly "ages" water allowing you to enjoy your pets in action quicker without fear of the negative impact of toxic chloramine, ammonia, chlorine, heavy metals or nitrite. Great For Freshwater, Marine or Pond Environments.

Destroys Chloramines Removes Ammonia Removes Chlorine Detoxifies Nitrite Detoxifies Heavy Metals (including Copper) Adds Essential Electrolytes Boosts Alkalinity Replaces Skin Slime-Coat Reduces Fish Stress Instantly "Ages" Water Makes A Safe Environment For Your Aquatic Pets Non-Toxic To Humans, Pets and Aquatic Life.

Pond Solutions Ultimate is a full-function water conditioner that efficiently makes pond and aquarium water safe for fish. It removes chlorine and chloramines, detoxifies nitrite and heavy metals, and eliminates toxic ammonia while replenishing your fishes' protective slime coats.

• Full-function water conditioner for ponds and large aquariums
• Eliminates toxic ammonia, chlorine, nitrites, heavy metals and more
• Replaces protective slime coat on fish skin

Ultimate effectively removes trace copper from the water while providing essential electrolytes for your fishes' health. It boosts alkalinity, reduces stress and instantly "ages" the water to an ideal state for your aquatic pets. Ultimate is non-toxic to humans, pets and aquatic life. Made by Hikari, one of the most trusted names in pond care.

Made in the USA.

Directions for Use: To fully condition water for (1) new aquariums or ponds (2) after or during water additions, or (3) before adding new fishes, amphibians, invertebrates or plants, add 1 teaspoonful (5 ml) of Ultimate per 10 gallons of water. For larger applications add 1 oz per 60 gallons of water.

Ingredients: ClorAm-X, Electrolytes, Buffers and a proprietary polymer formula in aqueous solution.

Pond Solutions Ultimate is a full-function water conditioner that efficiently makes pond and aquarium water safe for fish. It removes chlorine and chloramines, detoxifies nitrite and heavy metals, and eliminates toxic ammonia while replenishing your fishes' protective slime coats.

• Full-function water conditioner for ponds and large aquariums
• Eliminates toxic ammonia, chlorine, nitrites, heavy metals and more
• Replaces protective slime coat on fish skin

Ultimate effectively removes trace copper from the water while providing essential electrolytes for your fishes' health. It boosts alkalinity, reduces stress and instantly "ages" the water to an ideal state for your aquatic pets. Ultimate is non-toxic to humans, pets and aquatic life. Made by Hikari, one of the most trusted names in pond care.

Made in the USA.

Directions for Use: To fully condition water for (1) new aquariums or ponds (2) after or during water additions, or (3) before adding new fishes, amphibians, invertebrates or plants, add 1 teaspoonful (5 ml) of Ultimate per 10 gallons of water. For larger applications add 1 oz per 60 gallons of water.

Ingredients: ClorAm-X, Electrolytes, Buffers and a proprietary polymer formula in aqueous solution.

Pond Solutions Ultimate is a full-function water conditioner that efficiently makes pond and aquarium water safe for fish. It removes chlorine and chloramines, detoxifies nitrite and heavy metals, and eliminates toxic ammonia while replenishing your fishes' protective slime coats.

• Full-function water conditioner for ponds and large aquariums
• Eliminates toxic ammonia, chlorine, nitrites, heavy metals and more
• Replaces protective slime coat on fish skin

Ultimate effectively removes trace copper from the water while providing essential electrolytes for your fishes' health. It boosts alkalinity, reduces stress and instantly "ages" the water to an ideal state for your aquatic pets. Ultimate is non-toxic to humans, pets and aquatic life. Made by Hikari, one of the most trusted names in pond care.

Made in the USA.

Directions for Use: To fully condition water for (1) new aquariums or ponds (2) after or during water additions, or (3) before adding new fishes, amphibians, invertebrates or plants, add 1 teaspoonful (5 ml) of Ultimate per 10 gallons of water. For larger applications add 1 oz per 60 gallons of water.

Ingredients: ClorAm-X, Electrolytes, Buffers and a proprietary polymer formula in aqueous solution.

Seachem Stability quickly stabilizes new aquarium environments and establishes the bio-filter for rapid, safe startup. Its unique blend of aerobic, anaerobic and facultative bacteria break down organic waste and toxic ammonia, nitrate and nitrite to prevent "new tank syndrome," the #1 cause of fish death.

• New tank stabilization system for marine and freshwater
• Rapidly and safely establishes bio-filter
• Prevents fish death from "new tank syndrome"

Unlike competing products, the bacteria employed by Stability are non-sulfur fixing and will not produce toxic hydrogen sulfide. Stability is completely harmless to all aquatic organisms (including aquatic plants) so there is no danger of overuse. The result of nearly a decade of research and development, Seachem Stability represents the current state of the art in natural biological management.

Directions: Use 1 capful (5 mL) for each 40 L (10 gallons) on the first day with a new aquarium. After that use 1 capful for each 80 L (20 gallons) daily for 7 days. Fish and other aquatic species may be introduced at any time as long as dosage is maintained for 7 days. For optimum bio-filter performance use 1 capful for each 40 L (10 gallons) once a month or with each water change, whenever introducing new fish, or whenever medicating an aquarium.

Tip: Use along with Seachem Prime when setting up a new tank to create an ideal safe environment for your fish.

Seachem Stability quickly stabilizes new aquarium environments and establishes the bio-filter for rapid, safe startup. Its unique blend of aerobic, anaerobic and facultative bacteria break down organic waste and toxic ammonia, nitrate and nitrite to prevent "new tank syndrome," the #1 cause of fish death.

• New tank stabilization system for marine and freshwater
• Rapidly and safely establishes bio-filter
• Prevents fish death from "new tank syndrome"

Unlike competing products, the bacteria employed by Stability are non-sulfur fixing and will not produce toxic hydrogen sulfide. Stability is completely harmless to all aquatic organisms (including aquatic plants) so there is no danger of overuse. The result of nearly a decade of research and development, Seachem Stability represents the current state of the art in natural biological management.

Directions: Use 1 capful (5 mL) for each 40 L (10 gallons) on the first day with a new aquarium. After that use 1 capful for each 80 L (20 gallons) daily for 7 days. Fish and other aquatic species may be introduced at any time as long as dosage is maintained for 7 days. For optimum bio-filter performance use 1 capful for each 40 L (10 gallons) once a month or with each water change, whenever introducing new fish, or whenever medicating an aquarium.

Tip: Use along with Seachem Prime when setting up a new tank to create an ideal safe environment for your fish.

Seachem Stability quickly stabilizes new aquarium environments and establishes the bio-filter for rapid, safe startup. Its unique blend of aerobic, anaerobic and facultative bacteria break down organic waste and toxic ammonia, nitrate and nitrite to prevent "new tank syndrome," the #1 cause of fish death.

• New tank stabilization system for marine and freshwater
• Rapidly and safely establishes bio-filter
• Prevents fish death from "new tank syndrome"

Unlike competing products, the bacteria employed by Stability are non-sulfur fixing and will not produce toxic hydrogen sulfide. Stability is completely harmless to all aquatic organisms (including aquatic plants) so there is no danger of overuse. The result of nearly a decade of research and development, Seachem Stability represents the current state of the art in natural biological management.

Directions: Use 1 capful (5 mL) for each 40 L (10 gallons) on the first day with a new aquarium. After that use 1 capful for each 80 L (20 gallons) daily for 7 days. Fish and other aquatic species may be introduced at any time as long as dosage is maintained for 7 days. For optimum bio-filter performance use 1 capful for each 40 L (10 gallons) once a month or with each water change, whenever introducing new fish, or whenever medicating an aquarium.

Tip: Use along with Seachem Prime when setting up a new tank to create an ideal safe environment for your fish.

Seachem Stability quickly stabilizes new aquarium environments and establishes the bio-filter for rapid, safe startup. Its unique blend of aerobic, anaerobic and facultative bacteria break down organic waste and toxic ammonia, nitrate and nitrite to prevent "new tank syndrome," the #1 cause of fish death.

• New tank stabilization system for marine and freshwater
• Rapidly and safely establishes bio-filter
• Prevents fish death from "new tank syndrome"

Unlike competing products, the bacteria employed by Stability are non-sulfur fixing and will not produce toxic hydrogen sulfide. Stability is completely harmless to all aquatic organisms (including aquatic plants) so there is no danger of overuse. The result of nearly a decade of research and development, Seachem Stability represents the current state of the art in natural biological management.

Directions: Use 1 capful (5 mL) for each 40 L (10 gallons) on the first day with a new aquarium. After that use 1 capful for each 80 L (20 gallons) daily for 7 days. Fish and other aquatic species may be introduced at any time as long as dosage is maintained for 7 days. For optimum bio-filter performance use 1 capful for each 40 L (10 gallons) once a month or with each water change, whenever introducing new fish, or whenever medicating an aquarium.

Tip: Use along with Seachem Prime when setting up a new tank to create an ideal safe environment for your fish.

Seachem Stability quickly stabilizes new aquarium environments and establishes the bio-filter for rapid, safe startup. Its unique blend of aerobic, anaerobic and facultative bacteria break down organic waste and toxic ammonia, nitrate and nitrite to prevent "new tank syndrome," the #1 cause of fish death.

• New tank stabilization system for marine and freshwater
• Rapidly and safely establishes bio-filter
• Prevents fish death from "new tank syndrome"

Unlike competing products, the bacteria employed by Stability are non-sulfur fixing and will not produce toxic hydrogen sulfide. Stability is completely harmless to all aquatic organisms (including aquatic plants) so there is no danger of overuse. The result of nearly a decade of research and development, Seachem Stability represents the current state of the art in natural biological management.

Directions: Use 1 capful (5 mL) for each 40 L (10 gallons) on the first day with a new aquarium. After that use 1 capful for each 80 L (20 gallons) daily for 7 days. Fish and other aquatic species may be introduced at any time as long as dosage is maintained for 7 days. For optimum bio-filter performance use 1 capful for each 40 L (10 gallons) once a month or with each water change, whenever introducing new fish, or whenever medicating an aquarium.

Tip: Use along with Seachem Prime when setting up a new tank to create an ideal safe environment for your fish.

SeaChem De-Nitrate removes nitrates, nitrites, ammonia, and organics from both freshwater and marine aquariums. The high porosity of De-Nitrate supports the proliferation of both aerobic and anaerobic bacteria that further remove these toxic aquarium byproducts.

• Removes nitrates, nitrites, ammonia and organics
• Supports growth of beneficial bacteria that eliminate toxins
• Suitable for fresh and saltwater tanks

Even when exhausted as an organic adsorbent, SeaChem De-Nitrate continues to be an excellent support for the biological filter and does not have to be removed.

Directions: Place De-Nitrate to assure the flow of water through it, such as in a canister filter, chemical filtration module, or box filter. Flow rate should not exceed 200 L (50 gallons) per hour. If higher flow rates are unavoidable, use Matrix or Pond Matrix. It is best to rinse off dust before use. Once De-Nitrate has been used for several days, nitrate concentrations should start to fall and level off gradually at a concentration of 4-5 mg/L as nitrate. As long as nitrate concentrations remain under control, the product is not exhausted. Each 500 mL of De-Nitrate treats about 100-200 L (25-50 gallons), depending on initial nitrate concentration and the current biological load. Enough should be used to remove nitrate at a rate at least as fast as the rate of formation. If very high nitrates are initially present, they should be brought down to less than 20 mg/L with water changes.

SeaChem De-Nitrate removes nitrates, nitrites, ammonia, and organics from both freshwater and marine aquariums. The high porosity of De-Nitrate supports the proliferation of both aerobic and anaerobic bacteria that further remove these toxic aquarium byproducts.

• Removes nitrates, nitrites, ammonia and organics
• Supports growth of beneficial bacteria that eliminate toxins
• Suitable for fresh and saltwater tanks

Even when exhausted as an organic adsorbent, SeaChem De-Nitrate continues to be an excellent support for the biological filter and does not have to be removed.

Directions: Place De-Nitrate to assure the flow of water through it, such as in a canister filter, chemical filtration module, or box filter. Flow rate should not exceed 200 L (50 gallons) per hour. If higher flow rates are unavoidable, use Matrix or Pond Matrix. It is best to rinse off dust before use. Once De-Nitrate has been used for several days, nitrate concentrations should start to fall and level off gradually at a concentration of 4-5 mg/L as nitrate. As long as nitrate concentrations remain under control, the product is not exhausted. Each 500 mL of De-Nitrate treats about 100-200 L (25-50 gallons), depending on initial nitrate concentration and the current biological load. Enough should be used to remove nitrate at a rate at least as fast as the rate of formation. If very high nitrates are initially present, they should be brought down to less than 20 mg/L with water changes.

SeaChem De-Nitrate removes nitrates, nitrites, ammonia, and organics from both freshwater and marine aquariums. The high porosity of De-Nitrate supports the proliferation of both aerobic and anaerobic bacteria that further remove these toxic aquarium byproducts.

• Removes nitrates, nitrites, ammonia and organics
• Supports growth of beneficial bacteria that eliminate toxins
• Suitable for fresh and saltwater tanks

Even when exhausted as an organic adsorbent, SeaChem De-Nitrate continues to be an excellent support for the biological filter and does not have to be removed.

Directions: Place De-Nitrate to assure the flow of water through it, such as in a canister filter, chemical filtration module, or box filter. Flow rate should not exceed 200 L (50 gallons) per hour. If higher flow rates are unavoidable, use Matrix or Pond Matrix. It is best to rinse off dust before use. Once De-Nitrate has been used for several days, nitrate concentrations should start to fall and level off gradually at a concentration of 4-5 mg/L as nitrate. As long as nitrate concentrations remain under control, the product is not exhausted. Each 500 mL of De-Nitrate treats about 100-200 L (25-50 gallons), depending on initial nitrate concentration and the current biological load. Enough should be used to remove nitrate at a rate at least as fast as the rate of formation. If very high nitrates are initially present, they should be brought down to less than 20 mg/L with water changes.

SeaChem De-Nitrate removes nitrates, nitrites, ammonia, and organics from both freshwater and marine aquariums. The high porosity of De-Nitrate supports the proliferation of both aerobic and anaerobic bacteria that further remove these toxic aquarium byproducts.

• Removes nitrates, nitrites, ammonia and organics
• Supports growth of beneficial bacteria that eliminate toxins
• Suitable for fresh and saltwater tanks

Even when exhausted as an organic adsorbent, SeaChem De-Nitrate continues to be an excellent support for the biological filter and does not have to be removed.

Directions: Place De-Nitrate to assure the flow of water through it, such as in a canister filter, chemical filtration module, or box filter. Flow rate should not exceed 200 L (50 gallons) per hour. If higher flow rates are unavoidable, use Matrix or Pond Matrix. It is best to rinse off dust before use. Once De-Nitrate has been used for several days, nitrate concentrations should start to fall and level off gradually at a concentration of 4-5 mg/L as nitrate. As long as nitrate concentrations remain under control, the product is not exhausted. Each 500 mL of De-Nitrate treats about 100-200 L (25-50 gallons), depending on initial nitrate concentration and the current biological load. Enough should be used to remove nitrate at a rate at least as fast as the rate of formation. If very high nitrates are initially present, they should be brought down to less than 20 mg/L with water changes.

Seachem Purigen Ultimate Filtration is a premium synthetic adsorbent that, unlike any other filtration product, is not a mixture of ion exchangers or adsorbents, but a unique macro-porous synthetic polymer that removes soluble and insoluble impurities from water at a rate and capacity that exceeds all others by over 500%.

• Removes soluble and insoluble impurities from water
• Controls ammonia, nitrites, nitrates
• Polishes water to unparalleled clarity

Purigen controls ammonia, nitrites and nitrates by removing nitrogenous organic waste that would otherwise release these harmful compounds. Purigens impact on trace elements is minimal. It significantly raises redox. It polishes water to unparalleled clarity. Purigen darkens progressively as it exhausts, and is easily renewed by treating with bleach. Purigen is designed for both marine and freshwater use.

Why Its Different:

• Selectivity: Purigen is the highest capacity organic filtration resin on the market. No other products can compare to its ability to clear haziness and polish water to unparalleled clarity. Unlike other products on the market which are simple ion-exchange resins, Purigen is specifically designed to be an organic scavenging resin. When ion-exchange resins are filled to capacity by metals and other contaminants, Purigen has barely begun to reach its potential. Purigen generally ignores simple elemental compounds, having an extreme affinity for nitrogenous organics. The primary source of nitrogenous compounds in an aquarium is waste. Fish, corals, even plants produce nitrogenous waste. Purigen removes that waste faster and more completely than anything else on the market.
• Capacity: Purigens possesses enhanced capacity owing to its vast surface area. All other resins on the market are purely spherical extruded beads. These beads remain smooth even under a microscope. Purigen is both spherical and macroreticular. It has microscopic pores that increase its usable surface area to many times that of a purely spherical resin.
• Regeneration: Purigen can also be regenerated. As it adsorbs waste products, Purigen will change color from a pale blonde to a dark brown, almost black. Once it is exhausted, it can be regenerated with a solution of bleach and water. The bleach will literally “burn off" the organics that have been removed from the tank. Watch out for products that claim to be regenerable with a brine solution. That is the regeneration procedure for ion-exchange purposes. A brine solution will not remove organics. While such resins have a limited capacity for organic adsorption, a brine regeneration process only replaces removed ionic compounds. It does not destroy large organic molecules that were removed, which is the primary function of organic adsorption resins.

Directions:
Rinse before use. Use in a fine mesh filter bag. Each 1 L treats up to 4,000 L (1,000 gallons) for up to six months. Exhaustion is indicated by a pronounced discoloration of the beads to dark brown or black.

Regeneration: Soak in a 1:1 bleach:water solution for 24 hours in a non-metalic container in a well ventilated area and away from children. Rinse well, then soak for 8 hours with a solution containing 2 tablespoons of ChlorGuard, Prime, or equivalent dechlorinator per cup of water. Rinse well. Original color and full activity should now be restored and Purigen is ready for reuse. Caution: some slime coat products may permanently foul Purigen and render regeneration difficult. Do not reuse if odor of chlorine is detectable. In case of doubt, soak beads in small quantity of water and test for residual chlorine with a chlorine test kit.

Dosage:
100 ml (Media Bag): Treats 106 Gallons
250 ml: Treats 265 Gallons
500 ml: Treats 530 Gallons
1 Liter: Treats 1,060 Gallons
2 Liters: Treats 2,120 Gallons

Seachem Purigen Ultimate Filtration is a premium synthetic adsorbent that, unlike any other filtration product, is not a mixture of ion exchangers or adsorbents, but a unique macro-porous synthetic polymer that removes soluble and insoluble impurities from water at a rate and capacity that exceeds all others by over 500%.

• Removes soluble and insoluble impurities from water
• Controls ammonia, nitrites, nitrates
• Polishes water to unparalleled clarity

Purigen controls ammonia, nitrites and nitrates by removing nitrogenous organic waste that would otherwise release these harmful compounds. Purigens impact on trace elements is minimal. It significantly raises redox. It polishes water to unparalleled clarity. Purigen darkens progressively as it exhausts, and is easily renewed by treating with bleach. Purigen is designed for both marine and freshwater use.

Why Its Different:

• Selectivity: Purigen is the highest capacity organic filtration resin on the market. No other products can compare to its ability to clear haziness and polish water to unparalleled clarity. Unlike other products on the market which are simple ion-exchange resins, Purigen is specifically designed to be an organic scavenging resin. When ion-exchange resins are filled to capacity by metals and other contaminants, Purigen has barely begun to reach its potential. Purigen generally ignores simple elemental compounds, having an extreme affinity for nitrogenous organics. The primary source of nitrogenous compounds in an aquarium is waste. Fish, corals, even plants produce nitrogenous waste. Purigen removes that waste faster and more completely than anything else on the market.
• Capacity: Purigens possesses enhanced capacity owing to its vast surface area. All other resins on the market are purely spherical extruded beads. These beads remain smooth even under a microscope. Purigen is both spherical and macroreticular. It has microscopic pores that increase its usable surface area to many times that of a purely spherical resin.
• Regeneration: Purigen can also be regenerated. As it adsorbs waste products, Purigen will change color from a pale blonde to a dark brown, almost black. Once it is exhausted, it can be regenerated with a solution of bleach and water. The bleach will literally “burn off" the organics that have been removed from the tank. Watch out for products that claim to be regenerable with a brine solution. That is the regeneration procedure for ion-exchange purposes. A brine solution will not remove organics. While such resins have a limited capacity for organic adsorption, a brine regeneration process only replaces removed ionic compounds. It does not destroy large organic molecules that were removed, which is the primary function of organic adsorption resins.

Directions:
Rinse before use. Use in a fine mesh filter bag. Each 1 L treats up to 4,000 L (1,000 gallons) for up to six months. Exhaustion is indicated by a pronounced discoloration of the beads to dark brown or black.

Regeneration: Soak in a 1:1 bleach:water solution for 24 hours in a non-metalic container in a well ventilated area and away from children. Rinse well, then soak for 8 hours with a solution containing 2 tablespoons of ChlorGuard, Prime, or equivalent dechlorinator per cup of water. Rinse well. Original color and full activity should now be restored and Purigen is ready for reuse. Caution: some slime coat products may permanently foul Purigen and render regeneration difficult. Do not reuse if odor of chlorine is detectable. In case of doubt, soak beads in small quantity of water and test for residual chlorine with a chlorine test kit.

Dosage:
100 ml (Media Bag): Treats 106 Gallons
250 ml: Treats 265 Gallons
500 ml: Treats 530 Gallons
1 Liter: Treats 1,060 Gallons
2 Liters: Treats 2,120 Gallons

Seachem Purigen Ultimate Filtration is a premium synthetic adsorbent that, unlike any other filtration product, is not a mixture of ion exchangers or adsorbents, but a unique macro-porous synthetic polymer that removes soluble and insoluble impurities from water at a rate and capacity that exceeds all others by over 500%.

• Removes soluble and insoluble impurities from water
• Controls ammonia, nitrites, nitrates
• Polishes water to unparalleled clarity

Purigen controls ammonia, nitrites and nitrates by removing nitrogenous organic waste that would otherwise release these harmful compounds. Purigens impact on trace elements is minimal. It significantly raises redox. It polishes water to unparalleled clarity. Purigen darkens progressively as it exhausts, and is easily renewed by treating with bleach. Purigen is designed for both marine and freshwater use.

Why Its Different:

• Selectivity: Purigen is the highest capacity organic filtration resin on the market. No other products can compare to its ability to clear haziness and polish water to unparalleled clarity. Unlike other products on the market which are simple ion-exchange resins, Purigen is specifically designed to be an organic scavenging resin. When ion-exchange resins are filled to capacity by metals and other contaminants, Purigen has barely begun to reach its potential. Purigen generally ignores simple elemental compounds, having an extreme affinity for nitrogenous organics. The primary source of nitrogenous compounds in an aquarium is waste. Fish, corals, even plants produce nitrogenous waste. Purigen removes that waste faster and more completely than anything else on the market.
• Capacity: Purigens possesses enhanced capacity owing to its vast surface area. All other resins on the market are purely spherical extruded beads. These beads remain smooth even under a microscope. Purigen is both spherical and macroreticular. It has microscopic pores that increase its usable surface area to many times that of a purely spherical resin.
• Regeneration: Purigen can also be regenerated. As it adsorbs waste products, Purigen will change color from a pale blonde to a dark brown, almost black. Once it is exhausted, it can be regenerated with a solution of bleach and water. The bleach will literally “burn off" the organics that have been removed from the tank. Watch out for products that claim to be regenerable with a brine solution. That is the regeneration procedure for ion-exchange purposes. A brine solution will not remove organics. While such resins have a limited capacity for organic adsorption, a brine regeneration process only replaces removed ionic compounds. It does not destroy large organic molecules that were removed, which is the primary function of organic adsorption resins.

Directions:
Rinse before use. Use in a fine mesh filter bag. Each 1 L treats up to 4,000 L (1,000 gallons) for up to six months. Exhaustion is indicated by a pronounced discoloration of the beads to dark brown or black.

Regeneration: Soak in a 1:1 bleach:water solution for 24 hours in a non-metalic container in a well ventilated area and away from children. Rinse well, then soak for 8 hours with a solution containing 2 tablespoons of ChlorGuard, Prime, or equivalent dechlorinator per cup of water. Rinse well. Original color and full activity should now be restored and Purigen is ready for reuse. Caution: some slime coat products may permanently foul Purigen and render regeneration difficult. Do not reuse if odor of chlorine is detectable. In case of doubt, soak beads in small quantity of water and test for residual chlorine with a chlorine test kit.

Dosage:
100 ml (Media Bag): Treats 106 Gallons
250 ml: Treats 265 Gallons
500 ml: Treats 530 Gallons
1 Liter: Treats 1,060 Gallons
2 Liters: Treats 2,120 Gallons

Seachem Purigen Ultimate Filtration is a premium synthetic adsorbent that, unlike any other filtration product, is not a mixture of ion exchangers or adsorbents, but a unique macro-porous synthetic polymer that removes soluble and insoluble impurities from water at a rate and capacity that exceeds all others by over 500%.

• Removes soluble and insoluble impurities from water
• Controls ammonia, nitrites, nitrates
• Polishes water to unparalleled clarity

Purigen controls ammonia, nitrites and nitrates by removing nitrogenous organic waste that would otherwise release these harmful compounds. Purigens impact on trace elements is minimal. It significantly raises redox. It polishes water to unparalleled clarity. Purigen darkens progressively as it exhausts, and is easily renewed by treating with bleach. Purigen is designed for both marine and freshwater use.

Why Its Different:

• Selectivity: Purigen is the highest capacity organic filtration resin on the market. No other products can compare to its ability to clear haziness and polish water to unparalleled clarity. Unlike other products on the market which are simple ion-exchange resins, Purigen is specifically designed to be an organic scavenging resin. When ion-exchange resins are filled to capacity by metals and other contaminants, Purigen has barely begun to reach its potential. Purigen generally ignores simple elemental compounds, having an extreme affinity for nitrogenous organics. The primary source of nitrogenous compounds in an aquarium is waste. Fish, corals, even plants produce nitrogenous waste. Purigen removes that waste faster and more completely than anything else on the market.
• Capacity: Purigens possesses enhanced capacity owing to its vast surface area. All other resins on the market are purely spherical extruded beads. These beads remain smooth even under a microscope. Purigen is both spherical and macroreticular. It has microscopic pores that increase its usable surface area to many times that of a purely spherical resin.
• Regeneration: Purigen can also be regenerated. As it adsorbs waste products, Purigen will change color from a pale blonde to a dark brown, almost black. Once it is exhausted, it can be regenerated with a solution of bleach and water. The bleach will literally “burn off" the organics that have been removed from the tank. Watch out for products that claim to be regenerable with a brine solution. That is the regeneration procedure for ion-exchange purposes. A brine solution will not remove organics. While such resins have a limited capacity for organic adsorption, a brine regeneration process only replaces removed ionic compounds. It does not destroy large organic molecules that were removed, which is the primary function of organic adsorption resins.

Directions:
Rinse before use. Use in a fine mesh filter bag. Each 1 L treats up to 4,000 L (1,000 gallons) for up to six months. Exhaustion is indicated by a pronounced discoloration of the beads to dark brown or black.

Regeneration: Soak in a 1:1 bleach:water solution for 24 hours in a non-metalic container in a well ventilated area and away from children. Rinse well, then soak for 8 hours with a solution containing 2 tablespoons of ChlorGuard, Prime, or equivalent dechlorinator per cup of water. Rinse well. Original color and full activity should now be restored and Purigen is ready for reuse. Caution: some slime coat products may permanently foul Purigen and render regeneration difficult. Do not reuse if odor of chlorine is detectable. In case of doubt, soak beads in small quantity of water and test for residual chlorine with a chlorine test kit.

Dosage:
100 ml (Media Bag): Treats 106 Gallons
250 ml: Treats 265 Gallons
500 ml: Treats 530 Gallons
1 Liter: Treats 1,060 Gallons
2 Liters: Treats 2,120 Gallons

Seachem Purigen Ultimate Filtration is a premium synthetic adsorbent that, unlike any other filtration product, is not a mixture of ion exchangers or adsorbents, but a unique macro-porous synthetic polymer that removes soluble and insoluble impurities from water at a rate and capacity that exceeds all others by over 500%.

• Removes soluble and insoluble impurities from water
• Controls ammonia, nitrites, nitrates
• Polishes water to unparalleled clarity

Purigen controls ammonia, nitrites and nitrates by removing nitrogenous organic waste that would otherwise release these harmful compounds. Purigens impact on trace elements is minimal. It significantly raises redox. It polishes water to unparalleled clarity. Purigen darkens progressively as it exhausts, and is easily renewed by treating with bleach. Purigen is designed for both marine and freshwater use.

Why Its Different:

• Selectivity: Purigen is the highest capacity organic filtration resin on the market. No other products can compare to its ability to clear haziness and polish water to unparalleled clarity. Unlike other products on the market which are simple ion-exchange resins, Purigen is specifically designed to be an organic scavenging resin. When ion-exchange resins are filled to capacity by metals and other contaminants, Purigen has barely begun to reach its potential. Purigen generally ignores simple elemental compounds, having an extreme affinity for nitrogenous organics. The primary source of nitrogenous compounds in an aquarium is waste. Fish, corals, even plants produce nitrogenous waste. Purigen removes that waste faster and more completely than anything else on the market.
• Capacity: Purigens possesses enhanced capacity owing to its vast surface area. All other resins on the market are purely spherical extruded beads. These beads remain smooth even under a microscope. Purigen is both spherical and macroreticular. It has microscopic pores that increase its usable surface area to many times that of a purely spherical resin.
• Regeneration: Purigen can also be regenerated. As it adsorbs waste products, Purigen will change color from a pale blonde to a dark brown, almost black. Once it is exhausted, it can be regenerated with a solution of bleach and water. The bleach will literally “burn off" the organics that have been removed from the tank. Watch out for products that claim to be regenerable with a brine solution. That is the regeneration procedure for ion-exchange purposes. A brine solution will not remove organics. While such resins have a limited capacity for organic adsorption, a brine regeneration process only replaces removed ionic compounds. It does not destroy large organic molecules that were removed, which is the primary function of organic adsorption resins.

Directions:
Rinse before use. Use in a fine mesh filter bag. Each 1 L treats up to 4,000 L (1,000 gallons) for up to six months. Exhaustion is indicated by a pronounced discoloration of the beads to dark brown or black.

Regeneration: Soak in a 1:1 bleach:water solution for 24 hours in a non-metalic container in a well ventilated area and away from children. Rinse well, then soak for 8 hours with a solution containing 2 tablespoons of ChlorGuard, Prime, or equivalent dechlorinator per cup of water. Rinse well. Original color and full activity should now be restored and Purigen is ready for reuse. Caution: some slime coat products may permanently foul Purigen and render regeneration difficult. Do not reuse if odor of chlorine is detectable. In case of doubt, soak beads in small quantity of water and test for residual chlorine with a chlorine test kit.

Dosage:
100 ml (Media Bag): Treats 106 Gallons
250 ml: Treats 265 Gallons
500 ml: Treats 530 Gallons
1 Liter: Treats 1,060 Gallons
2 Liters: Treats 2,120 Gallons

Seachem Garlic Guard is an appetite and flavor enhancer for freshwater and saltwater fish. Garlic Guard contains allicin (the naturally derived, active ingredient found in garlic), which has been demonstrated to possess health-promoting benefits, and will help renew the interest of poor or finicky eaters.

• Garlic additive and flavor enhancer
• Renews interest of poor or finicky eaters
• Suitable for fresh or saltwater; reef and plant safe

Allicin possesses strong antioxidant properties (similar to Vitamin C) which promote enhanced health through elimination of free radicals. For enhanced health benefits, Seachem Garlic Guard also contains Vitamin C. Safe for freshwater, marine and reef aquariums.

Directions for Use: Shake well before use. Soak food in Garlic Guard before feeding.

Guaranteed Analysis:
Garlic Extract - 9900 ppm
Allicin (active ingredient) - 130 ppm
Vitamin C - 1000 ppm

Seachem Garlic Guard is an appetite and flavor enhancer for freshwater and saltwater fish. Garlic Guard contains allicin (the naturally derived, active ingredient found in garlic), which has been demonstrated to possess health-promoting benefits, and will help renew the interest of poor or finicky eaters.

• Garlic additive and flavor enhancer
• Renews interest of poor or finicky eaters
• Suitable for fresh or saltwater; reef and plant safe

Allicin possesses strong antioxidant properties (similar to Vitamin C) which promote enhanced health through elimination of free radicals. For enhanced health benefits, Seachem Garlic Guard also contains Vitamin C. Safe for freshwater, marine and reef aquariums.

Directions for Use: Shake well before use. Soak food in Garlic Guard before feeding.

Guaranteed Analysis:
Garlic Extract - 9900 ppm
Allicin (active ingredient) - 130 ppm
Vitamin C - 1000 ppm

Seachem Garlic Guard is an appetite and flavor enhancer for freshwater and saltwater fish. Garlic Guard contains allicin (the naturally derived, active ingredient found in garlic), which has been demonstrated to possess health-promoting benefits, and will help renew the interest of poor or finicky eaters.

• Garlic additive and flavor enhancer
• Renews interest of poor or finicky eaters
• Suitable for fresh or saltwater; reef and plant safe

Allicin possesses strong antioxidant properties (similar to Vitamin C) which promote enhanced health through elimination of free radicals. For enhanced health benefits, Seachem Garlic Guard also contains Vitamin C. Safe for freshwater, marine and reef aquariums.

Directions for Use: Shake well before use. Soak food in Garlic Guard before feeding.

Guaranteed Analysis:
Garlic Extract - 9900 ppm
Allicin (active ingredient) - 130 ppm
Vitamin C - 1000 ppm

SeaChem PhosGuard rapidly removes phosphate and silicate from marine and freshwater aquaria. It is not recommended for phosphate buffered freshwater. SeaChem PhosGuard is highly porous for high capacity and bead-shaped for optimum water flow.

• Removes phosphate and silicate from fresh and saltwater systems
• Highly porous and bean-shaped for maximum absorption and water flow
• Causes a decline in hair algae and enhanced coral growth

SeaChem Phosguard outperforms all competing products. PhosGuard is a high capacity and high efficiency filtration product for removing phosphates and silicates from marine or fresh water aquaria. Unlike competing products, PhosGuard is bead-shaped for optimum flow characteristics and has an exceptional porosity for enhanced capacity. PhosGuard has a working capacity to remove 20 to 60 mg/l phosphate in 100 gallons with a similar impact on silicates. It may be used continuously or intermittently, and will not release removed phosphate. PhosGuard will cause a decline in hair algae and enhance coral growth. Each liter treats up to 300 gallons. Marine or freshwater use.

Instructions: Use 1 cup for every 75 gallons. Leave product in place for 4 days, then test phosphate and silicate.

SeaChem PhosGuard rapidly removes phosphate and silicate from marine and freshwater aquaria. It is not recommended for phosphate buffered freshwater. SeaChem PhosGuard is highly porous for high capacity and bead-shaped for optimum water flow.

• Removes phosphate and silicate from fresh and saltwater systems
• Highly porous and bean-shaped for maximum absorption and water flow
• Causes a decline in hair algae and enhanced coral growth

SeaChem Phosguard outperforms all competing products. PhosGuard is a high capacity and high efficiency filtration product for removing phosphates and silicates from marine or fresh water aquaria. Unlike competing products, PhosGuard is bead-shaped for optimum flow characteristics and has an exceptional porosity for enhanced capacity. PhosGuard has a working capacity to remove 20 to 60 mg/l phosphate in 100 gallons with a similar impact on silicates. It may be used continuously or intermittently, and will not release removed phosphate. PhosGuard will cause a decline in hair algae and enhance coral growth. Each liter treats up to 300 gallons. Marine or freshwater use.

Instructions: Use 1 cup for every 75 gallons. Leave product in place for 4 days, then test phosphate and silicate.

SeaChem PhosGuard rapidly removes phosphate and silicate from marine and freshwater aquaria. It is not recommended for phosphate buffered freshwater. SeaChem PhosGuard is highly porous for high capacity and bead-shaped for optimum water flow.

• Removes phosphate and silicate from fresh and saltwater systems
• Highly porous and bean-shaped for maximum absorption and water flow
• Causes a decline in hair algae and enhanced coral growth

SeaChem Phosguard outperforms all competing products. PhosGuard is a high capacity and high efficiency filtration product for removing phosphates and silicates from marine or fresh water aquaria. Unlike competing products, PhosGuard is bead-shaped for optimum flow characteristics and has an exceptional porosity for enhanced capacity. PhosGuard has a working capacity to remove 20 to 60 mg/l phosphate in 100 gallons with a similar impact on silicates. It may be used continuously or intermittently, and will not release removed phosphate. PhosGuard will cause a decline in hair algae and enhance coral growth. Each liter treats up to 300 gallons. Marine or freshwater use.

Instructions: Use 1 cup for every 75 gallons. Leave product in place for 4 days, then test phosphate and silicate.

SeaChem PhosGuard rapidly removes phosphate and silicate from marine and freshwater aquaria. It is not recommended for phosphate buffered freshwater. SeaChem PhosGuard is highly porous for high capacity and bead-shaped for optimum water flow.

• Removes phosphate and silicate from fresh and saltwater systems
• Highly porous and bean-shaped for maximum absorption and water flow
• Causes a decline in hair algae and enhanced coral growth

SeaChem Phosguard outperforms all competing products. PhosGuard is a high capacity and high efficiency filtration product for removing phosphates and silicates from marine or fresh water aquaria. Unlike competing products, PhosGuard is bead-shaped for optimum flow characteristics and has an exceptional porosity for enhanced capacity. PhosGuard has a working capacity to remove 20 to 60 mg/l phosphate in 100 gallons with a similar impact on silicates. It may be used continuously or intermittently, and will not release removed phosphate. PhosGuard will cause a decline in hair algae and enhance coral growth. Each liter treats up to 300 gallons. Marine or freshwater use.

Instructions: Use 1 cup for every 75 gallons. Leave product in place for 4 days, then test phosphate and silicate.

SeaChem PhosGuard rapidly removes phosphate and silicate from marine and freshwater aquaria. It is not recommended for phosphate buffered freshwater. SeaChem PhosGuard is highly porous for high capacity and bead-shaped for optimum water flow.

• Removes phosphate and silicate from fresh and saltwater systems
• Highly porous and bean-shaped for maximum absorption and water flow
• Causes a decline in hair algae and enhanced coral growth

SeaChem Phosguard outperforms all competing products. PhosGuard is a high capacity and high efficiency filtration product for removing phosphates and silicates from marine or fresh water aquaria. Unlike competing products, PhosGuard is bead-shaped for optimum flow characteristics and has an exceptional porosity for enhanced capacity. PhosGuard has a working capacity to remove 20 to 60 mg/l phosphate in 100 gallons with a similar impact on silicates. It may be used continuously or intermittently, and will not release removed phosphate. PhosGuard will cause a decline in hair algae and enhance coral growth. Each liter treats up to 300 gallons. Marine or freshwater use.

Instructions: Use 1 cup for every 75 gallons. Leave product in place for 4 days, then test phosphate and silicate.

Seachem live bearer/brackish aquarium salt is a chemically sound blend of salts designed to replicate the native environment of live bearers and other brackish estuary fish without adversely impacting on aquatic plants when used at regionally specific recommended dosage. The salt is also well suited for routine aquarium freshwater use. It does not impact pH or provide buffering. For low range pH control Use Acid buffer, discus buffer, South American Cichlid buffer 4. 5, or Acid regulator. Use neutral regulator, Central American Cichlid buffer or South American Cichlid buffer 7. 0 for neutral pH. For high range pH control Use alkaline regulator, alkaline buffer or Tanganyika buffer.

• A chemically sound blend of salts designed to replicate native environment of live bearers and other brackish estuary fish
• Designed to function without adversely impacting on aquatic plants when used at regionally specific recommended dosage
• Well suited for routine Aquarium freshwater dosage
• Does not impact pH or provide buffering
<

Seachem Alkaline Buffer raises the pH and alkalinity (KH) of your aquarium water and holds it steady between 7.2 and 8.5 - an ideal range for most freshwater environments. Alkaline Buffer is safe, gentle, and phosphate-free to reduce the risk of algae or cloudiness.

• Raises pH and increases alkalinity
• Buffers pH between 7.2 and 8.5
• Great for planted aquariums or very hard water

Seachem Alkaline Buffer is a sodium bicarbonate-based buffer. This makes it slightly less stable than phosphate buffers, but better suited for planted aquariums where adding more phosphates would lead to an algae problem.

Dosage:
300 grams (10.5 oz): Treats 860 Gallons
600 grams (1.3 lbs): Treats 1,720 Gallons
1.2 kg (2.6 lbs): Treats 3,440 Gallons
4 kg (8.8 lbs): Treats 11,640 Gallons

Directions: To increase pH, use 1 teaspoon (7g) for every 80 L (20 gallons) daily until the desired pH is reached (this dose raises alkalinity by about 1 meq/L (2.8 dKH)). For precise dosing, use the Seachem Digital Spoon Scale. In order to adjust pH gradually, use Alkaline Buffer with Acid Buffer.

FAQ:

• Q: What is the difference between Neutral Regulator, Discus Buffer, Alkaline Buffer, and Acid Buffer
  A: Neutral Regulator and Discus Buffer are phosphate-based buffers providing a very strong and stable buffering system. Alkaline Buffer and Acid Buffer are non-phosphate buffers, which although less stable than a phosphate buffer, are ideal for the planted aquarium where high phosphate levels would lead to an algae problem.
• Q: Is Alkaline Buffer a sodium bicarbonate
  A: Yes, it is a sodium bicarbonate-based buffer.

Seachem Alkaline Buffer raises the pH and alkalinity (KH) of your aquarium water and holds it steady between 7.2 and 8.5 - an ideal range for most freshwater environments. Alkaline Buffer is safe, gentle, and phosphate-free to reduce the risk of algae or cloudiness.

• Raises pH and increases alkalinity
• Buffers pH between 7.2 and 8.5
• Great for planted aquariums or very hard water

Seachem Alkaline Buffer is a sodium bicarbonate-based buffer. This makes it slightly less stable than phosphate buffers, but better suited for planted aquariums where adding more phosphates would lead to an algae problem.

Dosage:
300 grams (10.5 oz): Treats 860 Gallons
600 grams (1.3 lbs): Treats 1,720 Gallons
1.2 kg (2.6 lbs): Treats 3,440 Gallons
4 kg (8.8 lbs): Treats 11,640 Gallons

Directions: To increase pH, use 1 teaspoon (7g) for every 80 L (20 gallons) daily until the desired pH is reached (this dose raises alkalinity by about 1 meq/L (2.8 dKH)). For precise dosing, use the Seachem Digital Spoon Scale. In order to adjust pH gradually, use Alkaline Buffer with Acid Buffer.

FAQ:

• Q: What is the difference between Neutral Regulator, Discus Buffer, Alkaline Buffer, and Acid Buffer
  A: Neutral Regulator and Discus Buffer are phosphate-based buffers providing a very strong and stable buffering system. Alkaline Buffer and Acid Buffer are non-phosphate buffers, which although less stable than a phosphate buffer, are ideal for the planted aquarium where high phosphate levels would lead to an algae problem.
• Q: Is Alkaline Buffer a sodium bicarbonate
  A: Yes, it is a sodium bicarbonate-based buffer.

Seachem Alkaline Buffer raises the pH and alkalinity (KH) of your aquarium water and holds it steady between 7.2 and 8.5 - an ideal range for most freshwater environments. Alkaline Buffer is safe, gentle, and phosphate-free to reduce the risk of algae or cloudiness.

• Raises pH and increases alkalinity
• Buffers pH between 7.2 and 8.5
• Great for planted aquariums or very hard water

Seachem Alkaline Buffer is a sodium bicarbonate-based buffer. This makes it slightly less stable than phosphate buffers, but better suited for planted aquariums where adding more phosphates would lead to an algae problem.

Dosage:
300 grams (10.5 oz): Treats 860 Gallons
600 grams (1.3 lbs): Treats 1,720 Gallons
1.2 kg (2.6 lbs): Treats 3,440 Gallons
4 kg (8.8 lbs): Treats 11,640 Gallons

Directions: To increase pH, use 1 teaspoon (7g) for every 80 L (20 gallons) daily until the desired pH is reached (this dose raises alkalinity by about 1 meq/L (2.8 dKH)). For precise dosing, use the Seachem Digital Spoon Scale. In order to adjust pH gradually, use Alkaline Buffer with Acid Buffer.

FAQ:

• Q: What is the difference between Neutral Regulator, Discus Buffer, Alkaline Buffer, and Acid Buffer
  A: Neutral Regulator and Discus Buffer are phosphate-based buffers providing a very strong and stable buffering system. Alkaline Buffer and Acid Buffer are non-phosphate buffers, which although less stable than a phosphate buffer, are ideal for the planted aquarium where high phosphate levels would lead to an algae problem.
• Q: Is Alkaline Buffer a sodium bicarbonate
  A: Yes, it is a sodium bicarbonate-based buffer.

Seachem Alkaline Buffer raises the pH and alkalinity (KH) of your aquarium water and holds it steady between 7.2 and 8.5 - an ideal range for most freshwater environments. Alkaline Buffer is safe, gentle, and phosphate-free to reduce the risk of algae or cloudiness.

• Raises pH and increases alkalinity
• Buffers pH between 7.2 and 8.5
• Great for planted aquariums or very hard water

Seachem Alkaline Buffer is a sodium bicarbonate-based buffer. This makes it slightly less stable than phosphate buffers, but better suited for planted aquariums where adding more phosphates would lead to an algae problem.

Dosage:
300 grams (10.5 oz): Treats 860 Gallons
600 grams (1.3 lbs): Treats 1,720 Gallons
1.2 kg (2.6 lbs): Treats 3,440 Gallons
4 kg (8.8 lbs): Treats 11,640 Gallons

Directions: To increase pH, use 1 teaspoon (7g) for every 80 L (20 gallons) daily until the desired pH is reached (this dose raises alkalinity by about 1 meq/L (2.8 dKH)). For precise dosing, use the Seachem Digital Spoon Scale. In order to adjust pH gradually, use Alkaline Buffer with Acid Buffer.

FAQ:

• Q: What is the difference between Neutral Regulator, Discus Buffer, Alkaline Buffer, and Acid Buffer
  A: Neutral Regulator and Discus Buffer are phosphate-based buffers providing a very strong and stable buffering system. Alkaline Buffer and Acid Buffer are non-phosphate buffers, which although less stable than a phosphate buffer, are ideal for the planted aquarium where high phosphate levels would lead to an algae problem.
• Q: Is Alkaline Buffer a sodium bicarbonate
  A: Yes, it is a sodium bicarbonate-based buffer.

Seachem Acid Buffer is a non-phosphate buffer to lower pH and buffer with Alkaline Buffer. Both buffers are designed for the planted aquarium or for very hard water where phosphate buffers may pose an algae or cloudiness problem.

• Lowers aquarium pH and buffers from 6.0 to 8.0
• Converts alkalinity into CO2
• For the planted aquarium or very hard water

Seachem Acid Buffer lowers pH and buffers between 5.0 and 8.0 when used with Alkaline Buffer. As Acid Buffer lowers pH it converts carbonate alkalinity (KH) into available CO2. It may also be used to safely lower pH in marine water.

Directions: To lower pH, use 1/4 teaspoon (2g) for every 80 L (20 US gallons) daily until desired pH is reached (this dose lowers alkalinity by about 0.2 meq/L (0.6 dKH)). Larger doses may be required in very hard (KH) or alkaline waters.

Seachem Acid Buffer is a non-phosphate buffer to lower pH and buffer with Alkaline Buffer. Both buffers are designed for the planted aquarium or for very hard water where phosphate buffers may pose an algae or cloudiness problem.

• Lowers aquarium pH and buffers from 6.0 to 8.0
• Converts alkalinity into CO2
• For the planted aquarium or very hard water

Seachem Acid Buffer lowers pH and buffers between 5.0 and 8.0 when used with Alkaline Buffer. As Acid Buffer lowers pH it converts carbonate alkalinity (KH) into available CO2. It may also be used to safely lower pH in marine water.

Directions: To lower pH, use 1/4 teaspoon (2g) for every 80 L (20 US gallons) daily until desired pH is reached (this dose lowers alkalinity by about 0.2 meq/L (0.6 dKH)). Larger doses may be required in very hard (KH) or alkaline waters.

SeaChem Discus Buffer helps to replicate the ideal Discus environment (low pH and low GH (General Hardness)). Discus Buffer will lower pH and keep it lowered. Discus Buffer also softens water by precipitating calcium and magnesium.

• Adjusts pH to 5.8 - 6.8
• Helps to replicate the ideal Discus environment
• Softens water by precipitating calcium and magnesium

Use SeaChem Discus Trace to restore the proper level of trace elements required by thriving, healthy Discus.

Directions: Use 1 level teaspoon (7 g) for every 40-80 L (10-20 gallons) daily until intended pH is reached. Thereafter, use once a month or with water changes as required to maintain pH